精品久久久无码人妻中文字幕豆芽|S亚洲精品国产第一综合99久久|亚洲aⅴ无码一区二区波多野91|亚洲国产精品一在线观看一区二区|99一区二区三区国产热视频在线|99精品久久久久久中文字幕无码|免费一区二区三区爽视频高清中文网

  • Refrigerant Gas
  • Anaerobic Retaining Compound
  • Anaerobic Pipe Thread Sealant
  • Anaerobic Threadlocker
  • Anaerobic Flange Sealant
  • Industry Adhesive
  • Metal-filled Epoxy Putty
  • Silicone Potting Compound
  • RTV Silicone Gasket Maker
  • Modified Acrylic AB Glue
  • Epoxy AB Glue
moreimg_load
img_load
  • Refrigerant Gas R134a
    Refrigeran...
    Refrigeran...
  • Refrigerant Gas R22
    Refrigeran...
    Refrigeran...
  • Refrigerant Gas R290
    Refrigeran...
    Refrigeran...
  • Refrigerant Gas R600a
    Refrigeran...
    Refrigeran...
  • Refrigerant Gas R410a
    Refrigeran...
    Refrigeran...
  • Anaerobic Retaining Compound
  • Anaerobic Pipe Thread Sealant
  • Anaerobic Threadlocker
  • Anaerobic Flange Sealant
  • Industry Adhesive
  • Metal-filled Epoxy Putty
  • Silicone Potting Compound
  • RTV Silicone Gasket Maker
  • Modified Acrylic AB Glue
  • Epoxy AB Glue
moreimg_load
img_load
  • 638 Anaero...
    638 Anaero...
    638 Anaero...
  • 609 Anaero...
    609 Anaero...
    609 Anaero...
  • 603 Anaero...
    603 Anaero...
    603 Anaero...
ABOUT US
Industry
A high-tech enterprise specialized in engineering adhesive R&D and sale.
SERVICE
1 year warranty for all of our products
  • Anaerobic Threadlocker Instruction

    Anaerobic Threadlocker InstructionAnaerobic threadlocker can fill in thread engaging part gaps to enlarge engaging part area, so to make better locking porformance.The cured adhesive has good performance of corrosion resistance,shock resistance and leak-proof.l、 Use multifunctional cleaning agent to clean thread and bolt surface.2、Choose suitable part number of threadlockers depend on selection guide and main specification.3、 To use threadlocker to seal bold&nut like  picture 14、  To use threadlocker to seal blind screw like picture 2.5、  Tighten the nut to specified torque.  6、 Drip threadlocker to bolt and nut engaging part directly for assembled parts.Thread disassembly and assembly(1) In general condition, use normal wrench to disassemble the thread.(2)For thread which need high strength threadlocker or big diameter thread which is over M26, to heat the parts with adhesive to 230℃ then disassemble it.(3) Users need clean the previous adhesive,then apply threadlocker again if parts need reassembly.CautionsAnaerobic threadlockers can not be used for sealing pure oxygen or oxygen enriched system, and strong oxidizer pipeline like chlorine. 

    摘要標題

    標簽標題

  • Metal-filled Epoxy Putty Instruction

    Taisn Metal-filled Epoxy Putty Instruction1.Surface treatment:Ensure parts surface without oil, water, rust and dust.Make parts surface coarsening as much as possible to enlarge bonding area.Make sandblasting treatment if parts need high repairing strength.If casting parts remain oil and water, then use fire to remove it.2 .Clean&Dry:  Use Forsen brand multifunctional cleaning agent to clean the remained oil and dirt. Drying the parts in short time.3 Mix the repairing agent:  Metal-filled compound is combined of A-part and B-part. Mix A-part and B-part according to operating manual.Stir two parts uniformly until two colors become the same. Use up the repairing agent within specified time.4.Curing:The repairing agent cures at room temperature. Extend curing time or rise up temperature when temperature is under 15℃. Heat treatment can improve the repairing performance after initial cure. In normal condition, keep it warm at 80~100℃ for 3 hours can work well.5.Postprocessing: Users can process parts by traditional machining methods after the repairing agent cured for 8-12 hours.Note:1.Avoid processing it under 15℃ or when humity is higher than 90%.2.Parts surface to be glued shall keep dry, clean and rough.3.Apply suitable heating measures when temperature is under 15℃. 4.Users can use acetone or toluene to clean the repairing agent5.The repairing agent is non-toxic after curing, but don’t touch it by eyes or skin. Use clear water to clean immediately if it contact eyes.

    摘要標題

    標簽標題

乐山市| 哈巴河县| 栾城县| 元朗区| 义马市| 高州市| 茌平县| 平和县| 西乌| 尉犁县| 岳阳市| 迁西县| 会泽县| 水富县| 长治市| 白朗县| 拉萨市| 册亨县| 惠州市| 古蔺县| 左权县| 渑池县| 平江县| 潢川县| 漳州市| 奉贤区| 永平县| 称多县| 镇宁| 桦甸市| 奉贤区| 禄丰县| 滨州市| 洛川县| 临猗县| 山丹县| 东丽区| 桑日县| 吴忠市| 靖西县| 慈利县|